Fibrin-based tissue engineering: comparison of different methods of autologous fibrinogen isolation.

OBJECTIVE: This study is focussed on the optimal method of autologous fibrinogen isolation with regard to the yield and the use as a scaffold material. This is particularly relevant for pediatric patients with strictly limited volumes of blood. MATERIALS AND METHODS: The following isolation methods were evaluated: cryoprecipitation, ethanol (EtOH) precipitation, ammonium sulfate [(NH(4))(2)SO(4))] precipitation, ammonium sulfate precipitation combined with cryoprecipitation, and polyethylene glycol precipitation combined with cryoprecipitation. Fibrinogen yields were quantified spectrophotometrically and by electrophoretic analyses. To test the influence of the different isolation methods on the microstructure of the fibrin gels, scanning electron microscopy (SEM) was used and the mechanical strength of the cell-free and cell-seeded fibrin gels was tested by burst strength measurements. Cytotoxicity assays were performed to analyze the effect of various fibrinogen isolation methods on proliferation, apoptosis, and necrosis. Tissue development and cell migration were analyzed in all samples using immunohistochemical techniques. The synthesis of collagen as an extracellular matrix component by human umbilical cord artery smooth muscle cells in fibrin gels was measured using hydroxyproline assay. RESULTS: Compared to cryoprecipitation, all other considered methods were superior in quantitative analyses, with maximum fibrinogen yields of ∼80% of total plasma fibrinogen concentration using ethanol precipitation. SEM imaging demonstrated minor differences in the gel microstructure. Ethanol-precipitated fibrin gels exhibited the best mechanical properties. None of the isolation methods had a cytotoxic effect on the cells. Collagen production was similar in all gels except those from ammonium sulfate precipitation. Histological analysis showed good cell compatibility for ethanol-precipitated gels. CONCLUSION: The results of the present study demonstrated that ethanol precipitation is a simple and effective method for isolation of fibrinogen and a suitable alternative to cryoprecipitation. This technique allows minimization of the necessary blood volume for fibrinogen isolation, particularly important for pediatric applications, and also has no negative influence on microstructure, mechanical properties, cell proliferation, or tissue development.

Tissue-engineered small-caliber vascular graft based on a novel biodegradable composite fibrin-polylactide scaffold.

Small-caliber vascular grafts (< or =5 mm) constructed from synthetic materials for coronary bypass or peripheral vascular repair below the knee have poor patency rates, while autologous vessels may not be available for harvesting. The present study aimed to create a completely autologous small-caliber vascular graft by utilizing a bioabsorbable, macroporous poly(L/D)lactide 96/4 [P(L/D)LA 96/4] mesh as a support scaffold system combined with an autologous fibrin cell carrier material. A novel molding device was used to integrate a P(L/D)LA 96/4 mesh in the wall of a fibrin-based vascular graft, which was seeded with arterial smooth muscle cells (SMCs)/fibroblasts and subsequently lined with endothelial cells. The mold was connected to a bioreactor circuit for dynamic mechanical conditioning of the graft over a 21-day period. Graft cell phenotype, proliferation, extracellular matrix (ECM) content, and mechanical strength were analyzed. alpha-SMA-positive SMCs and fibroblasts deposited ECM proteins into the graft wall, with a significant increase in both cell number and collagen content over 21 days. A luminal endothelial cell lining was evidenced by vWf staining, while the grafts exhibited supraphysiological burst pressure (>460 mmHg) after dynamic cultivation. The results of our study demonstrated the successful production of an autologous, biodegradable small-caliber vascular graft in vitro, with remodeling capabilities and supraphysiological mechanical properties after 21 days in culture. The approach may be suitable for a variety of clinical applications, including coronary artery and peripheral artery bypass procedures.

Development of a composite degradable/nondegradable tissue-engineered vascular graft.

The present study aimed to determine the feasibility of constructing a reinforced autologous vascular graft by combining the advantages of fibrin gel as an autologous cell carrier material with the inherent mechanical strength of an integrated mesh structure. It was hypothesized that the mesh and dynamic culture conditions could be combined to generate mechanically stable and implantable vascular grafts within a shorter cultivation period than traditional methods. A two-step moulding technique was developed to integrate a polyvinylidene fluoride (PVDF) mesh (pore size: 1-2 mm) in the wall of a fibrin-based vascular graft (I.D. 5 mm) seeded with carotid myofibroblasts. The graft was cultured under increasing physiological flow conditions for 2 weeks. Histology, burst strength, and suture retention strength were evaluated. Cell growth and tissue development was excellent within the fibrin gel matrix surrounding the PVDF fibers, and tissue structure demonstrated remarkable similarity to native tissue. The grafts were successfully subjected to physiological flow rates and pressure gradients from the outset, and mechanical properties were enhanced by the mesh structure. Mean suture retention strength of the graft tissue was 6.3 N and the burst strength was 236 mm Hg. Using the vascular composite graft technique, the production of tissue engineered, small-caliber vascular grafts with good mechanical properties within a conditioning period of 14 days is feasible.

The in vitro development of autologous fibrin-based tissue-engineered heart valves through optimised dynamic conditioning.

Our group has previously demonstrated the synthesis of a completely autologous fibrin-based heart valve structure using the principles of tissue engineering. The present approach aims to guide more mature tissue development in fibrin-based valves based on in vitro conditioning in a custom-designed bioreactor system. Moulded fibrin-based tissue-engineered heart valves seeded with ovine carotid artery-derived cells were subjected to 12 days of mechanical conditioning in a bioreactor system. The bioreactor pulse rate was increased from 5 to 10 b.p.m. after 6 days, while a pressure difference of 20 mmH(2)O was maintained over the valve leaflets. Control valves were cultured under stirred conditions in a beaker. Cell phenotype and extracellular matrix (ECM) composition were analysed in all samples and compared to native ovine aortic valve tissue using routine histological and immunohistochemical techniques. Conditioned valve leaflets showed reduced tissue shrinkage compared to stirred controls. Limited ECM synthesis was evident in stirred controls, while the majority of cells were detached from the fibrin scaffold. Dynamic conditioning increased cell attachment/alignment and expression of alpha-smooth muscle actin, while enhancing the deposition of ECM proteins, including types I and III collagen, fibronectin, laminin and chondroitin sulphate. There was no evidence for elastin synthesis in either stirred controls or conditioned samples. The present study demonstrates that the application of low-pressure conditions and increasing pulsatile flow not only enhances seeded cell attachment and alignment within fibrin-based heart valves, but dramatically changes the manner in which these cells generate ECM proteins and remodel the valve matrix. Optimised dynamic conditioning, therefore, might accelerate the maturation of surgically feasible and implantable autologous fibrin-based tissue-engineered heart valves.